What is cable select jumper setting

what is cable select jumper setting

Jumper settings for Seagate and Maxtor ATA hard drives

Oct 24,  · Cable Select (CS) settings were designed to make it easier to connect hard drives by making it where you didn’t have worry about the Master or Slave jumper settings. You simply set the jumper to Cable Select on both drives and depending on where you connected them to the cable the computer would know which is Master and which is Slave. If you are going to use Cable Select Author: Jim Bernstein. Cable Select (CS) settings were designed to make it easier to connect hard drives because you didn't need to bother with setting the Master/Slave jumpers. You just connect the drives and depending on where you connected them to the cable the computer would know which is Master and which is Slave in theory. Now comes the confusing part.

Hard drives are the component of your computer that stores your files as well as what your operating system is installed on. If you didn't use a hard drive you would not be able to run your how to cook a paula deen spiral ham unless you temporarily booted it up from something like a CD or USB flash drive.

In order for a hard drive to be recognized by an operating system such as Windows, the computer needs to know that it exists, is connected properly, what size it is and so on. For IDE devices such as hard drives and CDROMs you need to make sure the jumpers are set correctly or else the computer won't recognize the drive and you won't be able to use it in your system.

Some cables may only come with sstting though. The slave drive does not rely on the master drive for its operation or vice versa. Most computers come with two IDE controller ports on the motherboard that will support two drives each for a total of 4 drives in the computer.

The only time you really need to worry about which drive is master and which is slave is when you are setting up your operating system drive on the primary IDE controller port.

What is cable select jumper setting should set id OS drive as master and connect it to the primary IDE port so it boots the computer correctly. When connecting more than one hard drive or other IDE device to a computer on the same IDE controller, you have to assign one as the primary or master and one as the secondary or slave using jumpers. The placement of the jumpers will vary on the hard drive. The drive should have a diagram on the back or top of the drive zelect what position to put the jumpers for what setting.

You simply set the jumper to Cable Select on both drives and depending on where you connected them to the cable the computer would know which is Master and which is Slave. If you are going to use Cable Select you need a special 40 conductor IDE cable that would determine master and slave connections. Most IDE cables you buy today should be of this type. If you set both drives on the same cable to master or slave then the computer most likely won't recognize the drives in the BIOS and therefore you won't be able to boot the computer with the drive or install your operating system on it.

So always check your settings when installing a new what is my ruling planet. If you are replacing an existing drive simply set the jumper to match the setting on the old drive.

Subscribe today! Click Here. Join Us On FaceBook. We Os. Join Us On Twitter Get insights into the computer industry and regular updates on our site. Wjat insights into the computer industry and regular updates on our site. New tech tip videos posted on a regular basis.

Share with Friends

Set the first hard disk jumper to Master (Cable Select can be used if you set the second hard drive selection to Cable Select). Connect the drive using the Master connector on the primary IDE cable. Set the second hard disk jumper to Slave (Use Cable Select if Cable Select was used on the first HDD). Cable Select. This setting is the default setting for ATA drives. With the Cable Select jumper set, the BIOS determines whether a drive is a master or a slave by its position on the UltraATA cable. If the drive is jumpered as cable select and is connected to the black connector on the end of the cable, it is recognized as the master drive for that ATA controller. If the drive is jumpered as cable select and is .

Master or single drive. If you are installing your Seagate hard drive as the only drive in the system or if it will be the primary boot drive for the system, the jumper should be set as Cable Select.

If you are installing the drive as an additional drive in your system, the drive should be set as Cable Select. This setting is the default setting for ATA drives. If the drive is jumpered as cable select and is connected to the black connector on the end of the cable, it is recognized as the master drive for that ATA controller.

If the drive is jumpered as cable select and is connected to the grey connector on the middle of the cable, it is recognized as the slave drive for that ATA controller. On Seagate drives only, set a jumper on pins 5 and 6 and a jumper on pins 7 and 8. Use this jumper setting only if the drive does not work as a master or cable select. Seagate recommends the use of newer UltraATA cables to achieve the best performance from your new Seagate hard drive. These UltraATA cables have 3 colored connectors, each connector has a specific purpose.

Be sure to plug the correct connector into the correct device. Other devices like CD-ROM drives, tape drives and CD burners are usually plugged into a separate cable which also connects to the motherboard. Maxtor and Quantum drives follow the jumper configuration noted below:. The drive is configured at the factory for a cable select setting. This allows the drive to assume the proper role of master or slave based on the connector used on the cable see the UltraATA cable figure above.

For the cable select setting to work properly, the cables you are using must support the cable select feature. Current UltraATA cables with the 3 colored connectors do support this feature.

3 thoughts on “What is cable select jumper setting

Add a comment

Your email will not be published. Required fields are marked *